Environmental Friendly Chemical Anchor Adhesive Shrinkage Proof Suitable For Indoor

420ml 2:1 Two Component Chemcial Anchor Adhesive For Thread Rods
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing glue,
Chemical anchoring system used for anchoring and rebar connections in concrete.

Item #: FixingChor142
Capacity: 420ml
Materials: Epoxy
Mixing Ratio: 2:1

From rebar dwelling on a high-traffic infrastructure retrofit project to DIY projects, Xinchor offers a wide variety of adhesive anchoring products to meet your need.

Our strong, versatile epoxy-based adhesives are ideal for anchoring threaded rod, rebar and smooth dowels in an assortment of base materials. And our acrylic formulations deliver consistent performance for high-strength anchor grouting in a wide range of weather conditions, curing fast even in water-saturated concrete.

Ideal for anchoring threaded rod, rebar and smooth in a variety of base materials, epoxy-based anchoring adhesives offer strength and versatility across a wide variety of applications. Xinchor Fixingchor series epoxy adhesives meet or are rigorously tested to meet 2009 IBC requirements for both cracked and uncracked concrete applications. As you would expect, we offers all the high-strength dispensing tools and other important accessories to increase productivity on any project.

A two-component, high strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole cleaning equipment. is designed for bonding threaded rod and reinforcing bar hardware into drilled holes in concrete base and solid masonry materials.

Pure Epoxy 3:1 resin is a high performance, two components pure epoxy resin system. Applied in one

single action this resin will produce a high performance, strong fixing with exceptionally high chemical resistance.

Solvent-free, epoxy resin based, two part high performance anchoring adhesive.

A two component chemical anchoring injection system.

A formulation derived from a special resin blend, with high bond strength,

developed principally to anchor threaded rods into concrete. Used widely for

installations in extremely cold temperature situations.

Xinchor FixingChor injection system is a composite mortar based on epoxy resin. The mortar consists of 2 components, which are mixed in the static mixer to form a perfectly mixed mortar mass and can therefore harden.

Xinchor FixingChor Series are available in various packaging solutions. From small 360ml to 650ml cartridge for processing large quantities of mortar. All cartridges are side-by-side cartridges and must therefore be pressed out with a dispenser.

Xinchor FixingChor composite mortar is ideal for subsequent reinforcement connections (rebar) as well as highly stressed fastenings in concrete - regardless of whether cracked or non-cracked. In particular, large drilling diameters and / or large anchoring depths can be implemented very well due to the long processing time. The extensive evaluation in accordance with the latest standards makes it possible to solve almost all fastening-related problems.

Approved for anchorings in

Concrete, cracked and non-cracked Applications

Rebar planting in concrete structures.

Railway or express way modification works

Structure reinforcement

Curtain wall installing

Bridge modification works

Keel fixing in out wall

ATTENTION

-If the gelling time expires, please use a new static mixer.

-Do not cut or shorten nozzles.

-It can be used again in the future by replacing the static mixer.

-Please ensure hole is properly cleaned. Hole may be damp but must be free from water.

-Do not install anchors when substrate temperature is less than 0°C.

-Do not install anchors when the temperature is less than 10°C.

-If the cartridge is not finished, please clean the opening, then put the plug back and cap tightly.

-At temperatures below 10°C should be warmed or stored in temperatures

of 10-30°C for 24hours prior to use to improve product flow and cure.

Established in 2005, Zhejiang Xinchor Technology Co., Ltd. Focuses on research, development, production and marketing for building reinforcement materials and chemical anchoring adhesive.

Our Headquarter and marketing center located in West Lake Technological Park in Hangzhou, only 2 hours driving from Shanghai Pudong Airport, as well as we have sales branches throughout China, we passed ISO9001-2008 certificate in 2010.

As the earliest reinforcement material providers, we have our products wide range applied to high-speed railway, nuclear power station, bridge, tunnel, subway, municipal and civil buildings, and maintain a long-term cooperative relationship with a number of well-known construction companies. As a professional manufacturer of reinforcement materials, with company spirit of "quality first, integrity management" purposes, we can provide good quality products for building and industry at home and abroad.

You are welcome to contact us, we would be delighted to be of service, providing advice and professional building reinforcement solutions.