3:1 Pure Epoxy Injectable Mortar, Injectable Anchor Adhesive, Rebar
Anchoring
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing
glue,
Chemical anchoring system used for anchoring and rebar connections
in concrete.
Strong, Versatile Epoxy Anchor Adhesives For Threaded Rod, Rebar
Item #: FixingChor158
Capacity: 585ml
Materials: Epoxy
Mixing Ratio: 3:1
Product Description:
3:1 Pure Epoxy Injectable Mortar, Injectable Anchor Adhesive, Rebar
Anchoring
with approvals for rebar connections and heavy-duty anchoring
Base material condition: Dry, Wet
Base materials: Concrete (cracked and uncracked), Masonry wall
Application Range
Fixing of handrails, balustrades and supports
Fixing of railings
For structural work:
Fixing of window and door frames
Rebar / steel reinforcement anchoring in new and refurbishment
works.
Threaded rods
Bolts and special fastening systems
Mechanical and electrical services installation
Anchoring of supports for ducting and equipment.
Metal Work, carpentry
Fixing of the following substrates:
Suitable for
Non-cracked concrete
Reinforcement bars
Concrete
Hard natural and reconstituted stone
Solid rock and masonry
For fixing of:
Steel constructions
Staircases
Consoles
Machines
High-racks
Wooden constructions
Reinforcement bars
Technical Parameter:
1. Basic parameters
1) Appearence
Part A (main): white cream
Part B (hardener): red cream / grey cream
2) Mixed Viscosity: 18-22Pa.s
3) Hardened density: 1.50±0.10g/cm3
4) Mixing ratio (Volume ratio): 390ml(3:1)
5) Shelf time: 24 months
2 Main Performance
| Testing project | Condition | Index |
| Gel Performance (According to China National Standard GB50728-2011) |
| Split Tensile Strength (MPa) | Under (23±2)℃, (50±5)%RH, tested by loading speed of 2mm/min | ≥8.5 |
| Flexural Strength (MPa) | ≥50 (no fragment damage) |
| Compressive Strength (MPa) | ≥60 |
| Bonding Capacity (According to China National Standard GB50728-2011) |
| Steel-Steel Tensile Shear Strength (MPa) | (23±2)℃ (50±5)%RH | ≥10 |
| Bonding strength of Ribbed steel bar (or screw) with concrete under
constrain drawing condition | (23±2)℃ (50±5)%RH | C30,Ф25,L=150mm | ≥11 |
| C60,Ф25,L=150mm | ≥17 |
| Steel-Steel T-peeling strength (mm) | (23±2)℃,(50±5)%RH | ≤25 |
| Non-volatile content | (105±2)℃,(180±5)min | ≥99% |
| Ageing resistance to heat and humidity 90d |
| Reduction rate of tensile strength | Under normal room temperature | ≤12% |
| (According to China National Standard JGJ145-2013) |
| Tensile Strength (after high temperature welding) | Dia12 Grade II steel, C30 concrete Hole dia.16mm, Depth: 150mm | 55.1N, 57.0N, 54.8N |
3 Technical Data
Anchoring Adhesive used with thread rod
| Thread Rod Dia |
C30 Concrete | M10 | M12 | M16 | M20 | M24 |
| Drilling Dia.(mm) | | 12 | 14 | 18 | 24 | 28 |
| Depth (mm) | | 90 | 110 | 145 | 180 | 220 |
| Damage Pulling force KN | Grade 5.8 Steel | 29 | 42.2 | 78.5 | 122.5 | 254.5 |
| Grade 8.8 Steel / A4 SS | 36.8 | 52.9 | 94.1 | 147.0 | 211.7 |
| Damage Cutting force KN | Grade 5.8 Steel | 17.4 | 25.3 | 47.1 | 73.5 | 105.9 |
| Grade 8.8 Steel | `27.8 | 40.5 | 75.3 | 117.6 | 169.4 |
| Designed Pulling force KN | | 12.0 | 17.02 | 30.6 | 52.4 | 75.2 |
| Designed Cutting Force KN | Grade 5.8 Steel | 12.2 | 17.6 | 32.9 | 51.5 | 74.1 |
| Grade 8.8 Steel | 18.6 | 27.0 | 50.2 | 78.4 | 113.0 |
| Holes for each | | 54 | 25 | 8 | 5 | 3 |
Processing Method
1 Tools
- Electrical hammer
- Air compressor
- Glue dispenser
- Hole cleaning brush
2 Attention
- Drill as per requested hole dia. and depth
- Clean the hole completely
- Inject from the bottom of the hole and pull out the gun slowly.
- After planting the bar, let the gel harden in still.
Drilling: As per technical data sheet
Cleaning: using air pump or compressed air and brush to clean the holes
completely.
Assembling and Injection: Mount the static mixer onto the bottle, push out some incomplete
mixed gel at the front part,then inject from the bottom of the
hole, to fill 1/2 to 2/3 depth of the hole.
Bar planting: spin slowly the rebar or thread rods into the hole, adjust up and
down for several times to make the gel average, but don’t touch it
during hardening time.
Curing and Maintenance: According to the temperature of the base materials, give enough
time to harden and start to load mounting until it hardened
completely.
Curing time:
| Operation and Curing time |
| Temperarure ℃ | -5 | 0 | 10 | 20 | ≥30 |
| Operation time (min) | 60 | 45 | 30 | 25 | 20 |
| Curing time (h) | 72 | 48 | 24 | 12 | 6 |
Consumption Chart (holes per cartridge)
| Anchor Rod dia. | M10 | M12 | M16 | M20 | M24 |
| Drilling Dia.(mm) | 12 | 14 | 18 | 24 | 28 |
| Depth (mm) | 90 | 110 | 145 | 180 | 220 |
| Each usage | 8ml | 13ml | 28ml | 62ml | 103ml |
| 360ml | 45 | 27 | | | |
| 390ml | 48 | 30 | 14 | 6 | 3 |
| 585ml | 73 | 45 | 20 | 9 | 5 |
| 650ml | 81 | 50 | 23 | 10 | 6 |
Our Product Lines:
- Carbon Fiber Reinforcement System: XQ-CFC 300gsm, 200gsm fabric
and adhesives XQ-XW
- Steel Bonding System: XQ-GZ Epoxy grouting adhesives, XQ-JGN
Plate bonding Adhesives
- Crack Repairing System: XQ-GF Crack grouting adhesives, XQ-FF
crack seal adhesives
- Chemical Anchoring 390ml(3:1), 585ml(3:1), 650ml(1:1),
Our History:
15 years from 2000, ISO9001 approved, 40 employees, 5000m2 plant
Our Quality
All passed China National Standard lab testing, and be similar to
CE and other countries standards
Our main product series:
-- Chemical Anchor series
Pure Epoxy Adhesive 360ml (5:1) 390ml(3:1) 585ml (3:1)
-- Carbon fiber reinforcement system,
XQ-XW carbon fiber epoxy adhesive
XQ-XB concrete surface leveling epoxy adhesive
XQ-CFC carbon fiber fabric 12K unidirectional 200gsm-600gsm
-- Concrete repair system
XQ-GF crack grouting adhesive
XQ-FF crack sealing adhesive
-- Steel bonding reinforcement system
XQ-JGN structural epoxy adhesive
XQ-GZ Grouting epoxy adhesive
XQ-FB edge sealing adhesive
