High Strength Anchoring Epoxy Low Odour Strong Stability Molecular
Structure
360ml 5:1 Two Component Adhesive Anchoring System For Structural
Strengthening
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing
glue,
Chemical anchoring system used for anchoring and rebar connections
in concrete.
Item #: FixingChor136
Capacity: 360ml
Materials: Epoxy
Mixing Ratio: 5:1
Application:
- All concrete building without embedded steel bar
- Reinforcement and reconstruction of buildings with concrete
- Reinforcement and reconstruction of Railway, Road, Bridge, Water
resources, Tunnel, etc.
- Reinforcement for equipment, pipeline installation, supports of
curtain wall.
Technical Parameter:
Main Performance
| Testing project | Condition | Index |
| Gel Performance (According to China National Standard GB50728-2011) |
| Splitting Tensile Strength (MPa) | Under (23±2)℃, (50±5)%RH, tested by loading speed of 2mm/min | ≥8.5 |
| Flexural Strength (MPa) | ≥50 (no fragment damage) |
| Compressive Strength (MPa) | ≥60 |
| Bonding Capacity (According to China National Standard GB50728-2011) |
| Steel-Steel Tensile Shear Strength (MPa) | (23±2)℃ (50±5)%RH | ≥10 |
| Bonding strength of Ribbed steel bar (or screw) with concrete under
constrain drawing condition | (23±2)℃ (50±5)%RH | C30,Ф25,L=150mm | ≥11 |
| C60,Ф25,L=150mm | ≥17 |
| Steel-Steel T-peeling strength (mm) | (23±2)℃,(50±5)%RH | ≤25 |
| Non-volatile content | (105±2)℃,(180±5)min | ≥99% |
| Ageing resistance to heat and humidity 90d |
| Reduction rate of tensile strength | Under normal room temperature | ≤12% |
| (According to China National Standard JGJ145-2013) |
| Tensile Strength (after high temperature welding) | Dia12 Grade II steel, C30 concrete Hole dia.16mm, Depth: 150mm | 55.1N, 57.0N, 54.8N |
Processing Method
1 Tools
- Electric hammer
- Hole cleaning brush
- Air compressor
- Glue gun
2 Attention
- Drill as per requested hole dia. and depth
- Clean the hole completely
- Inject from the bottom of the hole and pull out the gun slowly.
- After planting the bar, let the gel harden in still.
Drilling: As per technical data
Cleaning: using pump or compressed air and brush to clean the hole
completely.
Assembling and Injection: Mount the static mixer onto the bottle, push out some incomplete
mixed gel at the front part,then inject from the bottom of the
hole, to fill 1/2 to 2/3 depth of the hole.
Bar planting: spin slowly the bar or screw into the hole, adjust up and down for
several times to make the gel average, but don’t touch it during
hardening time.
Curing and Maintenance: According to the temperature of the base materials, give enough
time to harden and start to load mounting until it hardened
completely.
Curing time:
| Operation and Harden time |
| Temperarure ℃ | -5 | 0 | 10 | 20 | ≥30 |
| Operation time (min) | 60 | 45 | 30 | 25 | 20 |
| Harden time (h) | 72 | 48 | 24 | 12 | 6 |
Consumption Chart (holes per cartridge)
| Anchor Rod dia. | M10 | M12 | M16 | M20 | M24 |
| Drilling Dia.(mm) | 12 | 14 | 18 | 24 | 28 |
| Depth (mm) | 90 | 110 | 145 | 180 | 220 |
| Each usage | 8ml | 13ml | 28ml | 62ml | 103ml |
| 360ml | 45 | 27 | | | |
| 390ml | 48 | 30 | 14 | 6 | 3 |
| 585ml | 73 | 45 | 20 | 9 | 5 |
| 650ml | 81 | 50 | 23 | 10 | 6 |
Packaging:
- One cartridge with one mixer in carton
- 12pcs/20pcs/30pcs per carton.
- Xinchor label or your own label.
- EXP Date on the top of cartridge.
- Customized Packing.
| Item No. | Mixing | Standard Pack/Set | Pcs/Ctn | Ctn Size (cm) | Ctn/Pallet | Pallets/ 20'FCL | Pallets/ 40'FCL |
| FixingChor 136 | 5:1 | 360ml+ 1mixer | 20 | 27x27x27 | 60 | 10 | 20 |
| FixingChor 139 | 3:1 | 390ml+ 1mixer | 20 | 40x26x27 | 50 | 10 | 20 |
| FixingChor 158 | 3:1 | 585ml + 1mixer | 12 | 29x21.5x30 | 64 | 10 | 20 |
| FixingChor 140 | 1:1 | 400ml+ 1mixer | 30 | 49×30×26 | 40 | 10 | 20 |
| FixingChor 165 | 1:1 | 650ml+ 1mixer | 10 | 31.5×21×26 | 70 | 10 | 20 |
| FixingChor 142 | 2:1 | 420ml + 1mixer | 20 | 46x22x23 | 40 | 10 | 20 |
Shipping:
- Shipments can be arranged by sea, air, courier express.
- Courier express includes DHL, FedEx, TNT, UPS, EMS, SF, etc.
